KERNEL: Linux version 3.0.8+ (xufangduo@WServer) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #93 PREEMPT Tue Jul 17 10:22:46 CST 2012
CODENAME: REL
Mainboard: nuclear
BRAND: softwinners
CPU_ABI: armeabi-v7a
CPU_ABI2: armeabi
DEVICE: mid
DISPLAY: mid-eng 4.0.4 IMM76D 20120717 test-keys
FINGERPRINT: softwinners/mid/mid:4.0.4/IMM76D/20120717:eng/test-keys
HARDWARE: sun5i
ID: IMM76D
TAGS: test-keys

Processor : ARMv7 Processor rev 2 (v7l)
BogoMIPS : 1001.88
Features : swp half thumb fastmult vfp edsp neon vfpv3
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x3
CPU part : 0xc08
CPU revision : 2
Hardware : sun5i
Revision : 0000
Serial : 054107dd353430305048433316254145

GL_OES_texture_npot
GL_OES_compressed_ETC1_RGB8_texture
GL_OES_standard_derivatives
GL_OES_EGL_image
GL_OES_depth24
GL_ARM_rgba8
GL_ARM_mali_shader_binary
GL_OES_depth_texture
GL_OES_packed_depth_stencil
GL_EXT_texture_format_BGRA8888
GL_EXT_blend_minmax
GL_OES_EGL_image_external
GL_OES_EGL_sync
GL_OES_rgb8_rgba8
GL_EXT_multisampled_render_to_texture
GL_EXT_discard_framebuffer

<6>[ 3782.260000] usb 2-1: reset high speed USB device number 2 using sw-ehci
<4>[ 3782.410000] -r871xu_dev_remove, done
<4>[ 3782.410000] -rtw_drv_halt
<4>[ 3782.410000] sw_usb_disable_hcd: usbc_num = 1
<4>[ 3782.410000] [sw-ehci1]: sw_usb_disable_ehci
<4>[ 3782.410000] [sw-ehci1]: remove, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc09890cc
<6>[ 3782.410000] sw-ehci sw-ehci.1: remove, state 1
<6>[ 3782.410000] usb usb2: USB disconnect, device number 1
<6>[ 3782.410000] usb 2-1: USB disconnect, device number 2
<6>[ 3782.420000] sw-ehci sw-ehci.1: USB bus 2 deregistered
<4>[ 3782.420000] hci_port_configure en=0,config_cnt=2
<4>[ 3782.420000] usb_passby en=0,passly=2
<4>[ 3782.420000] [sw-ehci1]: close clock
<4>[ 3782.420000] [sw-ohci1]: sw_usb_disable_ohci
<4>[ 3782.420000] [sw-ohci1]: remove, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc09891e0
<6>[ 3782.420000] sw-ohci sw-ohci.1: remove, state 1
<6>[ 3782.420000] usb usb3: USB disconnect, device number 1
<6>[ 3782.420000] sw-ohci sw-ohci.1: USB bus 3 deregistered
<4>[ 3782.420000] [sw-ohci1]: Set USB Power OFF
<4>[ 3782.420000] usb_passby en=0,passly=1
<4>[ 3782.420000] hci_port_configure en=0,config_cnt=1
<4>[ 3782.420000] [sw-ohci1]: close clock
<4>[ 3787.760000] sw_usb_enable_hcd: usbc_num = 1
<4>[ 3787.760000] [sw-ehci1]: sw_usb_enable_ehci
<4>[ 3787.760000] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc09890cc
<4>[ 3787.760000] [sw-ehci1]: open clock
<4>[ 3787.810000] usb_passby en=1,passly=0
<4>[ 3787.810000] hci_port_configure en=1,config_cnt=0
<4>[ 3787.810000] [sw-ehci1]: Set USB Power ON
<6>[ 3787.820000] sw-ehci sw-ehci.1: SW USB2.0 `Enhanced` Host Controller (EHCI) Driver
<6>[ 3787.820000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
<6>[ 3787.820000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
<6>[ 3787.840000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
<4>[ 3787.840000] ehci_irq: port change detect
<6>[ 3787.840000] hub 2-0:1.0: USB hub found
<6>[ 3787.840000] hub 2-0:1.0: 1 port detected
<4>[ 3787.840000] [sw-ohci1]: sw_usb_enable_ohci
<4>[ 3787.840000] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc09891e0
<4>[ 3787.840000] [sw-ohci1]: open clock
<4>[ 3787.900000] hci_port_configure en=1,config_cnt=1
<4>[ 3787.900000] usb_passby en=1,passly=1
<6>[ 3787.900000] sw-ohci sw-ohci.1: SW USB2.0 `Open` Host Controller (OHCI) Driver
<6>[ 3787.900000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
<6>[ 3787.900000] sw-ohci sw-ohci.1: irq 40, io mem 0xf1c14400
<6>[ 3787.960000] hub 3-0:1.0: USB hub found
<6>[ 3787.960000] hub 3-0:1.0: 1 port detected
<4>[ 3787.960000] rtw driver version=v3.4.2_3727.20120404
<4>[ 3787.960000] Build at: Jul 5 2012 13:41:50
<4>[ 3787.960000] ##########rtw_suspend_lock_init ###########
<6>[ 3787.960000] usbcore: registered new interface driver rtl8192cu
<6>[ 3788.160000] usb 2-1: new high speed USB device number 2 using sw-ehci
<4>[ 3788.310000] register rtw_netdev_ops to netdev_ops
<4>[ 3788.310000] rtw_wdev_alloc
<4>[ 3788.310000] CHIP TYPE: RTL8188C_8192C
<4>[ 3788.310000]
<4>[ 3788.310000] usb_endpoint_descriptor(0):
<4>[ 3788.310000] bLength=7
<4>[ 3788.310000] bDescriptorType=5
<4>[ 3788.310000] bEndpointAddress=81
<4>[ 3788.310000] wMaxPacketSize=200
<4>[ 3788.310000] bInterval=0
<4>[ 3788.310000] RT_usb_endpoint_is_bulk_in = 1
<4>[ 3788.310000]
<4>[ 3788.310000] usb_endpoint_descriptor(1):
<4>[ 3788.310000] bLength=7
<4>[ 3788.310000] bDescriptorType=5
<4>[ 3788.310000] bEndpointAddress=2
<4>[ 3788.310000] wMaxPacketSize=200
<4>[ 3788.310000] bInterval=0
<4>[ 3788.310000] RT_usb_endpoint_is_bulk_out = 2
<4>[ 3788.310000]
<4>[ 3788.310000] usb_endpoint_descriptor(2):
<4>[ 3788.310000] bLength=7
<4>[ 3788.310000] bDescriptorType=5
<4>[ 3788.310000] bEndpointAddress=3
<4>[ 3788.310000] wMaxPacketSize=200
<4>[ 3788.310000] bInterval=0
<4>[ 3788.310000] RT_usb_endpoint_is_bulk_out = 3
<4>[ 3788.310000]
<4>[ 3788.310000] usb_endpoint_descriptor(3):
<4>[ 3788.310000] bLength=7
<4>[ 3788.310000] bDescriptorType=5
<4>[ 3788.310000] bEndpointAddress=84
<4>[ 3788.310000] wMaxPacketSize=40
<4>[ 3788.310000] bInterval=1
<4>[ 3788.310000] RT_usb_endpoint_is_int_in = 4, Interval = 1
<4>[ 3788.310000] nr_endpoint=4, in_num=2, out_num=2
<4>[ 3788.310000]
<4>[ 3788.310000] USB_SPEED_HIGH
<4>[ 3788.310000] Chip Version ID: VERSION_NORMAL_UMC_CHIP_88C_B_CUT.
<4>[ 3788.310000] RF_Type is 3!!
<4>[ 3788.320000] EEPROM type is E-FUSE
<4>[ 3788.320000] ====> ReadAdapterInfo8192C
<4>[ 3788.320000] Boot from EFUSE, Autoload OK !
<4>[ 3788.610000] EEPROMVID = 0x0bda
<4>[ 3788.610000] EEPROMPID = 0x8176
<4>[ 3788.610000] EEPROMCustomerID : 0x00
<4>[ 3788.610000] EEPROMSubCustomerID: 0x00
<4>[ 3788.610000] RT_CustomerID: 0x00
<4>[ 3788.610000] _ReadMACAddress MAC Address from EFUSE = 00:1b:01:00:0a:7e
<4>[ 3788.610000] EEPROMRegulatory = 0x0
<4>[ 3788.610000] _ReadBoardType(0)
<4>[ 3788.610000] BT Coexistance = disable
<4>[ 3788.610000] RT_ChannelPlan: 0x0a
<4>[ 3788.610000] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
<4>[ 3788.610000] ### PS params=> power_mgnt(1),usbss_enable(0) ###
<4>[ 3788.610000] ### AntDivCfg(0)
<4>[ 3788.610000] readAdapterInfo_8192CU(): REPLACEMENT = 1
<4>[ 3788.610000] <==== ReadAdapterInfo8192C in 290 ms
<4>[ 3788.610000] rtw_register_early_suspend
<4>[ 3788.610000] rtw_macaddr_cfg MAC Address = 00:1b:01:00:0a:7e
<4>[ 3788.610000] MAC Address from pnetdev->dev_addr= 00:1b:01:00:0a:7e
<4>[ 3788.610000] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
<4>[ 3788.790000] rtw_android_priv_cmd: Android private cmd "BLOCK 1" on wlan0
<5>[ 3788.790000] init: starting `wpa_supplicant`
<6>[ 3788.800000] init: Created socket `/dev/socket/wpa_wlan0` with mode `660`, user `1010`, group `1010`
<4>[ 3788.820000] cfg80211_rtw_change_iface call netdev_open
<4>[ 3788.820000] +871x_drv - drv_open, bup=0
<4>[ 3788.830000] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_UMC_B
<4>[ 3788.830000] FirmwareDownload92C accquire FW from embedded image
<4>[ 3788.830000] fw_ver=v80, fw_subver=0, sig=0x88c0
<4>[ 3788.890000] fw download ok!
<4>[ 3788.890000] Set RF Chip ID to RF_6052 and RF type to 1T1R.
<4>[ 3789.410000] IQK:Start!!!
<4>[ 3789.420000] Path A IQK Success!!
<4>[ 3789.430000] Path A IQK Success!!
<4>[ 3789.440000] IQK: final_candidate is 0
<4>[ 3789.440000] IQK: RegE94=104 RegE9C=11 RegEA4=fe RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
<4>[ 3789.440000] Path A IQ Calibration Success !
<4>[ 3789.550000] pdmpriv->TxPowerTrackControl = 1
<4>[ 3789.550000] MAC Address from REG_MACID = 00:1b:01:00:0a:7e
<4>[ 3789.550000] rtl8192cu_hal_init in 730ms
<4>[ 3789.550000] MAC Address = 00:1b:01:00:0a:7e
<4>[ 3789.560000] rtw_cfg80211_init_wiphy:rf_type=3
<4>[ 3789.560000] -871x_drv - drv_open, bup=1
<4>[ 3789.560000] cfg80211_rtw_change_iface, old_iftype=6, new_iftype=2
<4>[ 3789.560000] +871x_drv - drv_open, bup=1
<4>[ 3789.560000] -871x_drv - drv_open, bup=1
<4>[ 3789.560000] cfg80211_rtw_set_power_mgmt
<6>[ 3789.560000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 3789.560000] cfg80211_rtw_flush_pmksa
<4>[ 3789.580000] cfg80211_rtw_change_station
<4>[ 3789.580000] cfg80211_rtw_change_station
<4>[ 3789.580000] cfg80211_rtw_change_station
<4>[ 3789.580000] rtw_android_priv_cmd: Android private cmd "P2P_DEV_ADDR" on wlan0
<4>[ 3789.600000] rtw_android_priv_cmd: Android private cmd "BLOCK 0" on wlan0

# begin build properties
# autogenerated by buildinfo.sh
ro.build.id=IMM76D
ro.build.display.id=mid-eng 4.0.4 IMM76D 20120717 test-keys
ro.build.version.incremental=20120717
ro.build.version.sdk=15
ro.build.version.codename=REL
ro.build.version.release=4.0.4
ro.build.date=2012年 07月 17日 星期二 10:34:20 CST
ro.build.date.utc=1340678060
ro.build.type=eng
ro.build.user=xufangduo
ro.build.host=WServer
ro.build.tags=test-keys
ro.product.model=TAB-N8BS
ro.product.brand=softwinners
ro.product.name=mid
ro.product.device=mid
ro.product.board=nuclear
ro.product.cpu.abi=armeabi-v7a
ro.product.cpu.abi2=armeabi
ro.product.manufacturer=unknown
ro.product.locale.language=en
ro.product.locale.region=US
ro.wifi.channels=
ro.board.platform=exDroid
# ro.build.product is obsolete; use ro.product.device
ro.build.product=mid
# Do not try to parse ro.build.description or .fingerprint
ro.build.description=mid-eng 4.0.4 IMM76D 20120717 test-keys
ro.build.fingerprint=softwinners/mid/mid:4.0.4/IMM76D/20120717:eng/test-keys
ro.build.characteristics=tablet
# end build properties
#
# ADDITIONAL_BUILD_PROPERTIES
#
ro.com.android.dateformat=MM-dd-yyyy
ro.config.ringtone=Ring_Synth_04.ogg
ro.config.notification_sound=pixiedust.ogg
ro.config.alarm_alert=Alarm_Classic.ogg
dalvik.vm.heapsize=48m
ro.kernel.android.checkjni=0
persist.sys.timezone=Europe/Rome
persist.sys.language=it
persist.sys.country=IT
wifi.interface=wlan0
wifi.supplicant_scan_interval=15
debug.egl.hw=1
ro.opengles.version=131072
persist.sys.strictmode.visual=0
persist.sys.strictmode.disable=1
hwui.render_dirty_regions=false
persist.sys.usb.config=mass_storage
ro.sf.lcd_density=160
persist.service.adb.enable=0
ro.product.firmware=1.4rc3
ro.setupwizard.mode=OPTIONAL
net.bt.name=Android
dalvik.vm.stack-trace-file=/data/anr/traces.txt

8192cu 575431 0 - Live 0xbf14a000
rtl8150 10305 0 - Live 0xbf0b5000
mcs7830 7581 0 - Live 0xbf0af000
qf9700 9152 0 - Live 0xbf0a8000
asix 24601 0 - Live 0xbf09c000
usbnet 26229 3 mcs7830,qf9700,asix, Live 0xbf08f000
sun5i_csi0 30803 0 - Live 0xbf082000
gc0307 18580 1 - Live 0xbf079000
videobuf_dma_contig 6251 1 sun5i_csi0, Live 0xbf074000
videobuf_core 20242 2 sun5i_csi0,videobuf_dma_contig, Live 0xbf06a000
cedarx 9351 0 - Live 0xbf063000
sun4i_lockrotation 2581 2 - Live 0xbf05f000
mma7660 6857 0 - Live 0xbf059000
mali 150894 6 - Live 0xbf027000
ump 49138 17 mali, Live 0xbf014000
sw_keyboard 2749 0 - Live 0xbf010000
ft5x_ts 43609 0 - Live 0xbf000000

RAM: 448 MB

System RAM: 144.000MB
Mali Sdram: 64.000MB
System RAM: 304.000MB


Flash: 8 GB Build-in (7.421 GB actual)

nand: 7.421 GB