WEXLER BOOK_T7008
3 Steps to publish Your specification here:

1. Install SpecDevice
2. Run and decode your specs
3. Get your link (read more...)
General Specifications
ManufacturerWEXLER
ModelBOOK_T7008
Firmware4.0.3; 20120531; SDK15
CPU1 core; ARMv7 Processor rev 2 (v7l) exDroid; Max: 1008,0 MHz; Min: 60,0 MHz
Display800 x 480; DPI: 120; Evaluated Size: 7,8"
Touch screenMultitouch 5 points
GPUMali-400 MP; ARM; OpenGL ES-CM 1.1; OpenGL ES 2.0
RAM1024 MB (960 MB available)
Flash8 GB Build-in (7.421 GB actual)
Communications
PhoneNone
WiFi8192cu; IEEE 802.11 b/g/n; RealtekRTL8188/92; AP Mode
USB HostYes
BluetoothNo
GPSYes
Advanced Features
Front cameraPhoto: 0.3 MP; Max: 640x480; Video: 0.3 MP; Max: 640x480; Focus: auto; No flash
Back cameraNo
SensorsMXC622X (MEMSIC); range: 0...2; resolution: 0,153 (7,661%); power: 0,005mA;
VibratorYes
Supported languages40; Arabic; Bulgarian; Catalan; Czech; Danish; German; Greek; English; Spanish; Persian; Finnish; Filipino; French; Hebrew; Hindi; Croatian; Hungarian; Indonesian; Italian; Japanese; Korean; Lithuanian; Latvian; Norwegian; Dutch; Polish; Pashto; Portuguese; Romansh; Romanian; Russian; Slovak; Slovenian; Serbian; Swedish; Thai; Turkish; Ukrainian; Vietnamese; Chinese
BatteryTechnology: LiFe; Voltage: 3920
External USB EthernetRealtek 8150 based adapters; MCS7830 based adapters
SD Version:1.1 5

KERNEL: Linux version 3.0.8+ (android2@Linux) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #17 PREEMPT Tue May 29 15:45:11 CST 2012
CODENAME: REL
Mainboard: crane
BRAND: softwinners
CPU_ABI: armeabi-v7a
CPU_ABI2: armeabi
DEVICE: crane-evb-v13
DISPLAY: 20120531
FINGERPRINT: softwinners/crane_evb_v13/crane-evb-v13:4.0.3/IML74K/20120531:eng/
HARDWARE: sun4i
ID: IML74K
TAGS: unknown

Processor : ARMv7 Processor rev 2 (v7l)
BogoMIPS : 1001.88
Features : swp half thumb fastmult vfp edsp neon vfpv3
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x3
CPU part : 0xc08
CPU revision : 2
Hardware : sun4i
Revision : 0000
Serial : 03c12a5153564848807182531623674e

GL_OES_texture_npot
GL_OES_compressed_ETC1_RGB8_texture
GL_OES_standard_derivatives
GL_OES_EGL_image
GL_OES_depth24
GL_ARM_rgba8
GL_ARM_mali_shader_binary
GL_OES_depth_texture
GL_OES_packed_depth_stencil
GL_EXT_texture_format_BGRA8888
GL_EXT_blend_minmax
GL_OES_EGL_image_external
GL_OES_EGL_sync
GL_OES_rgb8_rgba8
GL_EXT_multisampled_render_to_texture
GL_EXT_discard_framebuffer

<7>[ 1003.621649] sw_usb_enable_hcd: usbc_num = 2
<7>[ 1003.621667] WRN:L872(drivers/usb/host/ehci_sun4i.c):ERR: not support sw_usb_enable_ehci
<7>[ 1003.621684] WRN:L758(drivers/usb/host/ohci_sun4i.c):ERR: not support sw_usb_enable_ohci
<7>[ 1003.621748] rtw driver version=v3.4.1_3418.20120217
<7>[ 1003.621758] Build at: May 14 2012 10:55:22
<7>[ 1003.621768] ##########rtw_suspend_lock_init ###########
<7>[ 1003.622260] register rtw_netdev_ops to netdev_ops
<7>[ 1003.622280] rtw_wdev_alloc
<7>[ 1003.626219] CHIP TYPE: RTL8188C_8192C
<7>[ 1003.626245]
<7>[ 1003.626250] usb_endpoint_descriptor(0):
<7>[ 1003.626259] bLength=7
<7>[ 1003.626266] bDescriptorType=5
<7>[ 1003.626273] bEndpointAddress=81
<7>[ 1003.626281] wMaxPacketSize=200
<7>[ 1003.626288] bInterval=0
<7>[ 1003.626295] RT_usb_endpoint_is_bulk_in = 1
<7>[ 1003.626304]
<7>[ 1003.626308] usb_endpoint_descriptor(1):
<7>[ 1003.626316] bLength=7
<7>[ 1003.626322] bDescriptorType=5
<7>[ 1003.626329] bEndpointAddress=2
<7>[ 1003.626336] wMaxPacketSize=200
<7>[ 1003.626343] bInterval=0
<7>[ 1003.626351] RT_usb_endpoint_is_bulk_out = 2
<7>[ 1003.626359]
<7>[ 1003.626363] usb_endpoint_descriptor(2):
<7>[ 1003.626371] bLength=7
<7>[ 1003.626377] bDescriptorType=5
<7>[ 1003.626384] bEndpointAddress=3
<7>[ 1003.626391] wMaxPacketSize=200
<7>[ 1003.626398] bInterval=0
<7>[ 1003.626405] RT_usb_endpoint_is_bulk_out = 3
<7>[ 1003.626413]
<7>[ 1003.626417] usb_endpoint_descriptor(3):
<7>[ 1003.626427] bLength=7
<7>[ 1003.626433] bDescriptorType=5
<7>[ 1003.626441] bEndpointAddress=84
<7>[ 1003.626541] wMaxPacketSize=40
<7>[ 1003.626549] bInterval=1
<7>[ 1003.626557] RT_usb_endpoint_is_int_in = 4, Interval = 1
<7>[ 1003.626567] nr_endpoint=4, in_num=2, out_num=2
<7>[ 1003.626574]
<7>[ 1003.626579] USB_SPEED_HIGH
<7>[ 1003.626875] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
<7>[ 1003.626888] RF_Type is 3!!
<7>[ 1003.627268] EEPROM type is E-FUSE
<7>[ 1003.627278] ====> ReadAdapterInfo8192C
<7>[ 1003.627391] Boot from EFUSE, Autoload OK !
<7>[ 1003.986539] EEPROMVID = 0x0bda
<7>[ 1003.989644] EEPROMPID = 0x8176
<7>[ 1003.992776] EEPROMCustomerID : 0x00
<7>[ 1003.996298] EEPROMSubCustomerID: 0x00
<7>[ 1004.000829] RT_CustomerID: 0x00
<7>[ 1004.004034] _ReadMACAddress MAC Address from EFUSE = 48:02:2a:e1:87:74
<7>[ 1004.015778] EEPROMRegulatory = 0x0
<7>[ 1004.019265] _ReadBoardType(0)
<7>[ 1004.023061] BT Coexistance = disable
<7>[ 1004.023077] RT_ChannelPlan: 0x0a
<7>[ 1004.023090] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(1)
<7>[ 1004.023103] ### PS params=> power_mgnt(1),usbss_enable(0) ###
<7>[ 1004.023112] ### AntDivCfg(0)
<7>[ 1004.023120] readAdapterInfo_8192CU(): REPLACEMENT = 0
<7>[ 1004.023136] <==== ReadAdapterInfo8192C in 400 ms
<7>[ 1004.024697] rtw_register_early_suspend
<7>[ 1004.024799]
<7>[ 1004.024807] padapter->pwrctrlpriv.bSupportRemoteWakeup~~~~~~
<7>[ 1004.024818]
<7>[ 1004.024822] padapter->pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~
<7>[ 1004.024860] rtw_macaddr_cfg MAC Address = 48:02:2a:e1:87:74
<7>[ 1004.024873] MAC Address from pnetdev->dev_addr= 48:02:2a:e1:87:74
<7>[ 1004.030190] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
<6>[ 1004.108729] usbcore: registered new interface driver rtl8192cu
<5>[ 1004.127051] init: starting `wpa_supplicant`
<7>[ 1004.129114] +871x_drv - drv_open, bup=0
<6>[ 1004.130707] init: Created socket `/dev/socket/wpa_wlan0` with mode `660`, user `1010`, group `1010`
<7>[ 1004.133571] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
<7>[ 1004.133591] FirmwareDownload92C accquire FW from embedded image
<7>[ 1004.133604] fw_ver=v79, fw_subver=0, sig=0x88c0
<7>[ 1004.220459] fw download ok!
<7>[ 1004.223706] Set RF Chip ID to RF_6052 and RF type to 1T1R.
<7>[ 1004.656901] IQK:Start!!!
<7>[ 1004.676278] Path A IQK Success!!
<7>[ 1004.684523] Path A IQK Success!!
<7>[ 1004.701548] IQK: final_candidate is 0
<7>[ 1004.706543] IQK: RegE94=101 RegE9C=13 RegEA4=fe RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
<7>[ 1004.706557] Path A IQ Calibration Success !
<7>[ 1004.741235] battery vol change: 70->69
<7>[ 1004.824657] pdmpriv->TxPowerTrackControl = 1
<7>[ 1004.833899] MAC Address from REG_MACID = 48:02:2a:e1:87:74
<7>[ 1004.843983] rtl8192cu_hal_init in 720ms
<7>[ 1004.848201] MAC Address = 48:02:2a:e1:87:74
<7>[ 1004.853190] rtw_cfg80211_init_wiphy:rf_type=3
<7>[ 1004.853205] -871x_drv - drv_open, bup=1
<7>[ 1004.853282] cfg80211_rtw_set_power_mgmt
<6>[ 1004.872520] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<7>[ 1006.850065] ==>pwr_state_check_handler .fw_state(0)
<7>[ 1006.850080] ==> rtw_ps_cmd , enqueue CMD
<7>[ 1006.862923] ==>rtw_ps_processor .fw_state(0)
<7>[ 1006.869898] ==>ips_enter cnts:1
<7>[ 1006.875220] ==>power_saving_ctrl_wk_hdl change rf to OFF...LED(0x00020808)....
<7>[ 1006.875231]
<7>[ 1006.884445] ===> rtw_ips_pwr_down...................
<7>[ 1006.884664] ====> rtw_ips_dev_unload...
<7>[ 1006.924307] usb_read_port_cancel
<7>[ 1006.928289] usb_write_port_cancel
<7>[ 1006.931825] ==> rtl8192cu_hal_deinit
<7>[ 1006.935688] bkeepfwalive(0)
<7>[ 1006.943687] card disble without HWSM...........
<7>[ 1006.953668] <=== rtw_ips_pwr_down..................... in 70ms
<7>[ 1011.338359] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
<7>[ 1011.338386]
<7>[ 1011.338390] rfpwrstate_check call ips_leave....
<7>[ 1011.338402] ==>ips_leave cnts:1
<7>[ 1011.338462] ===> rtw_ips_pwr_up..............
<7>[ 1011.338476] ===> ips_netdrv_open.........
<7>[ 1011.343786] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
<7>[ 1011.343802] FirmwareDownload92C accquire FW from embedded image
<7>[ 1011.343813] fw_ver=v79, fw_subver=0, sig=0x88c0
<7>[ 1011.416106] fw download ok!
<7>[ 1011.419471] Set RF Chip ID to RF_6052 and RF type to 1T1R.
<7>[ 1011.848711] IQK:Start!!!
<7>[ 1011.862199] Path A IQK Success!!
<7>[ 1011.879342] Path A IQK Success!!
<7>[ 1011.888332] IQK: final_candidate is 0
<7>[ 1011.892236] IQK: RegE94=102 RegE9C=13 RegEA4=ff RegEAC=1 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
<7>[ 1011.892244] Path A IQ Calibration Success !
<7>[ 1012.024711] pdmpriv->TxPowerTrackControl = 1
<7>[ 1012.033956] MAC Address from REG_MACID = 48:02:2a:e1:87:74
<7>[ 1012.039477] rtl8192cu_hal_init in 700ms
<7>[ 1012.043435] <=== rtw_ips_pwr_up.............. in 710ms
<7>[ 1012.053637] ==> ips_leave.....LED(0x00028080)...
<7>[ 1012.058661] set_mode = IW_MODE_INFRA
<7>[ 1012.061378] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
<7>[ 1014.105603] survey done event(14)
<7>[ 1014.115667] =>rtw_wx_set_essid
<7>[ 1014.121845] rtw_cfg80211_indicate_scan_done without scan req
<7>[ 1014.121925] <=rtw_wx_set_essid, ret 0
<7>[ 1014.122980] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
<7>[ 1014.123061] set_mode = IW_MODE_INFRA
<7>[ 1014.123853]
<7>[ 1014.123857] wpa_ie(length:22):
<7>[ 1014.123871] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x04
<7>[ 1014.123880] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
<7>[ 1014.123889] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
<7>[ 1014.124604] Set BSSID under fw_state=0x00000008
<7>[ 1014.124625] [by_bssid:1][assoc_ssid:][to_roaming:0] new candidate: Shaman(80:1f:02:8f:50:9e) rssi:-84
<7>[ 1014.124639] rtw_select_and_join_from_scanned_queue: candidate: Shaman(80:1f:02:8f:50:9e)
<7>[ 1014.124666] rtw_restructure_ht_ie IEEE80211_HT_CAP_MAX_AMSDU is set
<7>[ 1014.124679] link to Realtek 96B
<7>[ 1014.124705] =>rtw_wx_set_essid
<7>[ 1014.124711] ssid=Shaman, len=6
<7>[ 1014.124722] Set SSID under fw_state=0x00000088
<7>[ 1014.124730] <=rtw_wx_set_essid, ret 0
<7>[ 1014.126154] set ch/bw before connected
<7>[ 1014.599452] link to Realtek 96B
<7>[ 1014.602688] issue_deauth
<7>[ 1014.612601] OnAuthClient
<7>[ 1014.615205] network.SupportedRates[0]=82
<7>[ 1014.619124] network.SupportedRates[1]=84
<7>[ 1014.623093] network.SupportedRates[2]=8B
<7>[ 1014.627027] network.SupportedRates[3]=96
<7>[ 1014.630968] network.SupportedRates[4]=0C
<7>[ 1014.634887] network.SupportedRates[5]=12
<7>[ 1014.638810] network.SupportedRates[6]=18
<7>[ 1014.642760] network.SupportedRates[7]=24
<7>[ 1014.646679] network.SupportedRates[8]=30
<7>[ 1014.650613] network.SupportedRates[9]=48
<7>[ 1014.654533] network.SupportedRates[10]=60
<7>[ 1014.658542] network.SupportedRates[11]=6C
<7>[ 1014.662565] bssrate_len = 12
<7>[ 1014.678118] OnAssocRsp
<7>[ 1014.680576] report_join_res(5)
<7>[ 1014.683636] rtw_joinbss_update_network
<7>[ 1014.687402] +rtw_update_ht_cap()
<7>[ 1014.690670] rtw_joinbss_update_stainfo
<7>[ 1014.694429] rtw_cfg80211_indicate_connect
<6>[ 1014.699903] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<7>[ 1014.705934] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
<7>[ 1014.716316] WMM(0): 0, a42b
<7>[ 1014.716578] WMM(1): 0, a44f
<7>[ 1014.717905] WMM(2): 0, 5e4322
<7>[ 1014.718556] WMM(3): 0, 2f3222
<7>[ 1014.718964] [HW_VAR_ACM_CTRL] Write 0x0
<7>[ 1014.719789] HTOnAssocRsp
<7>[ 1014.764528] update raid entry, mask=0xfffff, arg=0xa0
<7>[ 1014.770677]
<7>[ 1014.770686] ~~~~stastakey:unicastkey

# begin build properties
# autogenerated by buildinfo.sh
ro.build.id=IML74K
ro.build.display.id=20120531
ro.build.version.incremental=20120531
ro.build.version.sdk=15
ro.build.version.codename=REL
ro.build.version.release=4.0.3
ro.build.date=2012年 05月 31日 星期四 15:56:37 CST
ro.build.date.utc=1338450997
ro.build.type=eng
ro.build.user=android2
ro.build.host=Linux
ro.build.tags=
ro.product.model=WEXLER.BOOK_T7008
ro.product.brand=softwinners
ro.product.name=crane_evb_v13
ro.product.device=crane-evb-v13
ro.product.board=crane
ro.product.cpu.abi=armeabi-v7a
ro.product.cpu.abi2=armeabi
ro.product.manufacturer=unknown
ro.product.locale.language=en
ro.product.locale.region=US
ro.wifi.channels=
ro.board.platform=exDroid
# ro.build.product is obsolete; use ro.product.device
ro.build.product=crane-evb-v13
# Do not try to parse ro.build.description or .fingerprint
ro.build.description=crane_evb_v13-eng 4.0.3 IML74K 20120531
ro.build.fingerprint=softwinners/crane_evb_v13/crane-evb-v13:4.0.3/IML74K/20120531:eng/
ro.build.characteristics=tablet
# end build properties
#
# ADDITIONAL_BUILD_PROPERTIES
#
ro.com.android.dateformat=MM-dd-yyyy
ro.config.ringtone=Ring_Synth_04.ogg
ro.config.notification_sound=pixiedust.ogg
ro.config.alarm_alert=Alarm_Classic.ogg
dalvik.vm.heapstartsize=5m
dalvik.vm.heapgrowthlimit=48m
dalvik.vm.heapsize=256m
ro.kernel.android.checkjni=0
persist.sys.timezone=Europe/Moscow
persist.sys.language=ru
persist.sys.country=RU
wifi.interface=wlan0
wifi.supplicant_scan_interval=15
debug.egl.hw=1
ro.display.switch=1
ro.opengles.version=131072
persist.sys.strictmode.visual=0
persist.sys.strictmode.disable=1
hwui.render_dirty_regions=false
persist.service.adb.enable=0
persist.sys.usb.config=mass_storage,adb
ro.sf.lcd_density=120
ro.product.firmware=1.2
ro.setupwizard.mode=OPTIONAL
net.bt.name=Android
dalvik.vm.stack-trace-file=/data/anr/traces.txt

8192cu 566489 0 - Live 0xbf190000
rtl8150 8910 0 - Live 0xbf0fd000
mcs7830 6557 0 - Live 0xbf0f7000
qf9700 8513 0 - Live 0xbf0f0000
asix 22500 0 - Live 0xbf0e5000
usbnet 23745 3 mcs7830,qf9700,asix, Live 0xbf0d9000
ov2655 13439 0 - Live 0xbf0bb000
gc2015 15311 0 - Live 0xbf0b3000
gt2005 16234 0 - Live 0xbf0ab000
mxc622x 4708 1 - Live 0xbf08b000
mecs 3776 2 - Live 0xbf087000
sun4i_vibrator 2278 0 - Live 0xbf083000
sun4i_csi1 26605 0 - Live 0xbf078000
sun4i_csi0 26905 0 - Live 0xbf06d000
gc0308 14208 1 - Live 0xbf05d000
videobuf_dma_contig 5659 2 sun4i_csi1,sun4i_csi0, Live 0xbf058000
videobuf_core 18067 3 sun4i_csi1,sun4i_csi0,videobuf_dma_contig, Live 0xbf04e000
ft5x_ts 45249 0 - Live 0xbf03e000
mali 130147 12 - Live 0xbf011000
ump 42058 17 mali, Live 0xbf000000

RAM: 1024 MB (960 MB available)

System RAM: 448.000MB
Mali Sdram: 64.000MB
System RAM: 512.000MB


Flash: 8 GB Build-in (7.421 GB actual)

nand: 7.421 GB


Find Similar devices
Same CPU:
Same Display resolution:
Same ro.build.description:
Link: Here I buy Chinese smartphones and tablets



NEW: View Full Database >>>

Latest:

Jlinksz P10
alps samsung
INFINIX MOBILITY LIMITED Infinix X623
motorola moto g14
Galaxy S21 Ultra 5G SM-G998B/DS
Sony C5303
Android S24 Ultra
samsung SM-A125F
deltainno DT1902A
samsung SM-M325FV
android vKB017E
welcome I15 Pro max
Google coral
Xiaomi MI 8
XIOAMI MIU 14_PRO
Xiaomi M2101K7BL
alps FF-5000
Hisilicon HiDPTAndroid
weipass WPOS-MINI
Android S26 Ultra
Amlogic TVBOX
Xiaomi 22041216G
I14 Pro Max pop
rockchip rkpx3
JPay Inc. JP5s Inmate Media Device
motorola moto g stylus (2023)
rockchip rkpx3
i14proMax
welcome S23 Ultra
alps S21 Ultra
alps tb8788p1_64_bsp_k419
alps I14 Pro Max
SK telesys Clear
realme RMX3834
Allwinner QUAD-CORE T507
Xiaomi M2010J19CG
motorola moto e6
Xiaomi 21061119DG
Allwinner OCTOPUS-CORE T8
TCL A507DL
alps C20 PRO
TCL T671G
Multilaser smartphone
alps 8227L_demo
CF Easy F otido2010 for 4pda
alps Galaxy S23 Ultra
OPPO CPH1823
alps S11
DW G18
alps C20 PRO